UPVC Window Handle Replacement

Replacing a damaged window handle is a relatively easy process, and with the right tools it can be done quickly. But it's essential to know the type of handle and its spindle's length prior buying a replacement.

Older uPVC windows have cockspur window handles which have spurs that protrude to secure a wedge-shaped cockspur striker plate. These can be either left or right-handed and need to match when replacing.

What kind of lock or handle do I have

There are a variety of window locks and handles made from upvc each with their distinct advantages and functions. The kind of handle you choose will determine the ease to open your windows and if the locking mechanism functions as intended. With time and regular use the handles made of upvc on your windows could get worn out and damaged. This makes them less secure and less effective. In some cases they might even fall off completely. It is essential to fix the handles on your window made of upvc immediately if you notice them falling off. This will stop possible burglaries and will keep your home secure.

It's a task that anyone can complete. With a few basic tools and the proper knowledge, this is a simple procedure that should take no longer than a couple of minutes. To get started you must determine the type of handle and lock you have on your window and then identify the best replacement window seals.

Inline Espagnolette Handles

They are usually found on the side of the window. They have a flat design and feature a latch that connects to the locking mechanism of the frame of the window when it is turned. Inline upvc handles have spindles that run through the middle of the handle and into the frame of the window to activate the latch.

Cockspur Handles

These handles are typically located on older uPVC windows and have an distinctive hook-shaped design. Cockspur handles are fitted with a single screw that secures the handle to the frame of the window and are not as secure as other types of window handles.

Tilt and Turn Handles

The tilt and turn handles are different from other upvc handles in that they can be turned to open the window and then lowered into the window to ventilate. In general, they have a 7mm spindle at the back of the handle. They are available in both left and right handed versions.

When you are purchasing replacement handles for upvc it is essential to measure the spindle's length since not all of them are the same size. Drop something into the middle of the hole to check the length. This is the largest spindle size that will fit in your windows.

What is the spindle?

uPVC window handles operate similarly to doors, by turning the handle to activate a latch inside the frame. This opens the window so it can be shut and opened. But, at times, these handles can become damaged, especially if they are regularly used or exposed to harsh weather conditions. You may need to replace the handles on your uPVC window if they are not operating correctly.

There are several different types of uPVC handles that are available, comprising Espag, Cockspur and Spaded handle options. These handles are designed in a variety of ways to fit into uPVC frames. Each handle style uses an individual spindle to lock the window mechanism. It is essential to determine the type of handle installed on your uPVC windows so that you can replace it with a suitable one.

You can find out what kind of uPVC handle you have by looking at the base section of the handle. A snap-in cover should be over the screw that holds the handle's base in place. Once you remove this and you'll be able to see the screw that holds the handle base in position. After both screws are removed you should be in a position to pull the handle away from the uPVC window.

After removing the uPVC handle, carefully unscrew it from the locking mechanism. Make note of the length of the spindle since you'll need to ensure that you purchase one that is the same length as your original handle and locking mechanism.

The spindle wears out and cannot operate the locking mechanism. This could be due to corrosion, damage due to constant use or an unreliable locking mechanism. If this occurs, it will be necessary to replace the window handle as well as the locking mechanism to restore complete functionality to your uPVC windows.

How do I take off the handle that was previously attached?

Through time and regular use, window handles may be damaged or destroyed, and if this happens it is crucial to repair them as soon as you can to ensure the security of your home. It is simple to replace a worn or damaged handle. The job can be completed in less than a minute without the need of special tools.

To take off the handle, first remove the screw that is located at the base of the handle. After the screw is removed, the handle will be removed. Another screw will be situated at the base of the handle. This can also be removed. Once both of these screws are removed, the handle can be completely detached from the base of the window.

After the handle has been removed, take the new handle and line up the fixing holes with the holes present in the window frame. If there is a cap or sticker on the new handle, remove it if needed and put the handle back in place. It is important to check that the handle works once it is installed. Turn the handle over and make sure that the lock mechanism is in place.

Espag handles come with an extra spindle that is protruding from the handle and slots into a multipoint locking mechanism within the frame of the window. Cadenza windows have blades with cut-outs that slot into the lock mechanism while Cockspur handles have a long nose that is able to hook over either the frame's outer or transom bar cross member inside the window.

Once you have the new handle in place, slide the spindle into the lock in the window and then tighten it down. Once the handle is firmly fixated then replace the snap-in cover and the screw cap (if applicable). When the handle is ready to use, open and close the window a couple of times to make sure that it functions properly and Window Handle Replacement securely.

How do I install the new handle?

It's not difficult to alter the handle on your windows made of uPVC. The procedure is easy. All you require is a screwdriver and a little bit of patience. The first thing to do is to ensure that the handle you have previously used is not locked and then remove any screws that are visible, you can also replace these with screw caps if required. After you have removed the handle, you'll need to record the length of spindle that extends from the back. This is important as it will determine the type of handle that you will require to purchase.

Espagnolette handles that are made of uPVC are the most well-known kind of handle. The spindle passes through the handle to control the locking mechanism within the frame of the window. The handle opens the latch, allowing the window to open. Over time and through regular use, espagnolette handles can be damaged or destroyed, making it necessary to locate an alternative.

Cadenza handles are another type of uPVC window handle, which is typically used on tilt and turn windows. They have a protruding knife that works with a multiple-point locking mechanism within the window. They are generally more secure than espagnolette handles since they can only be opened from the inside. They can be replaced with the same method as espagnolette handles, however you should ensure that the new handle has an angled blade instead of one that is flat.

Once you have determined the right handle for you then you can place the new handle to the existing screw holes and then screw it into the appropriate position. Then, put the screw covers on and test your new handle. This is done by moving the handle from the locked to the unlocked position and the reverse direction several times. If you encounter any issues, it could be beneficial to speak with a professional to see if they are able to assist you in solving the issue. They can provide advice on how to fix the problem in a timely and effective way.