How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners must follow a set of steps that are unique to add an additional ignition key. This requires an electronic handheld computer, referred to as Tech-2 which is used by the dealer. Then a new key and transponder are required to be purchased and programmed to the car.

It is recommended to rotate your keys so that one does not get damaged faster than the other. This will also ensure that your keys remain in top condition.

Replacement Case

As opposed to the traditional Saab keys of old keys, the new key fobs contain electronics which makes it hard to duplicate. This has made stealing car keys much more difficult than it was twenty years ago. It also makes it more costly to replace keys that were lost.

Every owner of a saab key replacement 9-3 must have at least two working keys. If one of them is lost, it costs a fortune to add another to the car since it requires replacing the CIM module, and then reprogramming the locking cylinders. Dealers usually charge between $100-$200 for this.

There are several ways to get around these expensive. Some parts dealers will use the code of a spare key to cut a new metal blade at a fraction the cost of the dealer. The key must be exactly the same as the original for it to function in your vehicle.

Follow these steps to replace the case. You'll require a flathead screwdriver and some patience. Utilizing the screwdriver, slowly pull the plastic apart and separate the emergency key from the case. Once you have the case opened, take out the electronics and place them into the new case. Make sure you insert the correct key and badge inside the case.

Replacement Battery

The replacement battery for the Saab 9-3 is a low-cost component that can be replaced easily and quickly. This DIY video from YouTube Cyclone Cyd shows how to replace the battery for the remote key fob in just four steps. This tutorial will work with any modern Saab key fob. However, the procedure could differ slightly.

The first step is to find the button that lets off the backup key in the fob. It's usually near the Saab logo on the back of the fob. Use a flathead to insert the screwdriver into the small hole in this button. This will allow you to open the fob's case so that you can replace the battery.

After you have installed the new batteries CR1632, you can reassemble the remote key fob. Then, you can program it into your car. The whole process should not be more than an hour. It's a simple procedure that doesn't require special tools.

If you lose a key, the procedure will be more complicated but it is still able to be done. The dealer will first need to read the VIN of the vehicle before requesting an alternative TWICE module, as well as a key blade with the proper unique code. Then, they'll have to cut the replacement key and then program it with a new software tool called MDI.

Replacement Key Fob

The key fob is a device that locks and unlocks your car, it's got batteries inside. The batteries last for a certain time that is a long time, and they eventually go out of service. This is a regular issue that affects all cars, and the good news is that you can change the batteries in most key fobs without replacing the entire case. You can buy replacement fobs on Amazon that have all the electronics already in place, service so you'll just pop open the case and replace the batteries in the original case. It is important to keep in mind that you'll have to take out the emergency key first, and you can do this by putting a small flathead screwdriver into the slot that is located in the middle of the case. The screwdriver should be moved around the case until it is split open, making it easy to remove.

If you're ready to change your keys, make sure you have a spare in your possession. This will save you lots of money. If you have a spare, you can request that the dealer cut a new key and program it to your car, which is much cheaper than replacing the whole key fob.

It is possible to add a second key to your vehicle even if you don't have one, service but it takes some research and effort. A second key can cost several hundred dollars and it also requires the programming of the car's computer. This can be accomplished by a professional, however it is an expensive option for most owners.

Replacement Ignition

The current SAAB 9-3 features a more sophisticated alarm system built on a keycode. If you lose your only key, it can be costly to purchase a new one since the car needs to be equipped with a specific computer and also be programmed to accept a brand new key. Dealers can even charge hundreds of dollars to program an entirely new key, in the event that they are unable to complete the task.

If you've lost your only working key the dealer will replace your car's computer (known as the CIM or saab key replacement near me TWICE) to create the replacement, and will charge top dollar for it. We can reprogram the existing EEPROM in your car computer to be ready for an extra key. This will save you more than 50% on what you would have to pay an auto dealer.

If you have owned a SAAB 9-3 an extended period of time you are aware that the ignition keys aren't very durable. They can become extremely sticky and the buttons can be removed from them occasionally and you should think about replacing your ignition key if it isn't functioning properly. Luckily, replacing the ignition key isn't as difficult as it seems, and it can be done in a short time using the right tools.