Reasons Your fiat panda remote key replacement 500 Key Fob Won't Work

A key fob for fiat car Keys the Fiat 500 makes it simple to open doors and start your car. There are a myriad of reasons why the key fob might stop working. These include a dead battery water damage, receiver module issues, and interfering.

This listing is for an NEW replacement fiat 500 spare key cost Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

The most common reason the 500 key fob won't function is an inactive battery. Modern key fobs have a limited operating range, and must be within just a few feet of the vehicle to function. If you're far away from your vehicle, and you press the key fob button, the car will not respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin cell battery (Part number CR2032) with a new one from a reputable manufacturer such as Panasonic, Duracell, or Energizer. They are available at your local hardware store or on the internet.

After you've changed the battery on the coin cell You can test it by standing in front of your Fiat Car Keys 500 and pressing the buttons. The car should blink its parking lights, and fiat Car keys the key fob should operate the lock and unlock buttons.

If the key fob won't work after replacing the battery, it may be damaged by water that blocks it from connecting to the receiver module inside your car. Water damage can occur in a number of ways, ranging from an accidental splash to submerging the fob into salt water at the beach. If you suspect that your fob has been exposed to water, you can place it in a rice bag to draw out the moisture. If this doesn't work, your fob may require reprogramming by an experienced locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water out of the chip's electronic circuit it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can be particularly harmful to the fob's circuit board and can cause it to short out and eventually end up dying. The fob getting wet is not a good idea but if you drop it in the water in a cup or forget to remove it from your pocket before you run the washing machine and you don't have a chance, don't give in.

First, remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or another similar product and then dry it completely before replacing the battery. Test the fob next to determine if it's functioning. If the key does not work, it may have to be reset. This is usually done by a professional or dealer auto locksmith.

If your key is older and has not been programmed for your car it is necessary to replace it completely. This is a simple process that can be completed by a professional locksmith for automotive use. The locksmith will need the key to be cut to match your car's ignition. The locksmith will also need to reprogram your fob into the car's system. This is a quick and affordable process that is usually completed within the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob could stop working is that it's simply out of range. The remote's range is of 30 feet. So when you're too far away from your vehicle it won't be able to respond to your commands. You can easily solve this issue by moving the remote closer to your car until it responds.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and your fob doesn't function it could be due to an internal circuit board issue. Reprogramming your fob can resolve this problem. You can find the steps for most vehicles on YouTube or in the owner's guide.

It could be necessary to replace the metal clips that hold the coin batteries in their place. If they lose tension, they could stop the battery from being seated properly and could cause the remote to malfunction.

In rare instances it is possible that the fob will become disconnected from your vehicle due to software or hardware issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances, they may need to reinstall the program in your body control module, too.

Interference

Interference can also cause the key fob to not be able to receive or transmit an signal. This could occur if the key fob is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob could not function because of a weak connection to the buttons, water damage or damage to the internal chips.

If the key fob stopped working one day out of the blue or after trying everything you can at home to solve it e.g. replacing the battery, reprogramming it and using the spare key fob, you could have a faulty receiver module on your 500. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands that are then translated by the vehicle.

Fortunately, there's an easy way to reset all on-board systems in your 500, including the key fob. Disconnect the battery 12 volt for approximately 15 minutes by removing the negative cable and then the positive cable. Then reconnect the battery. This will clear out any residual electricity and restart the car's computer system, which can help you the key fob to function again. If the issue continues you should speak with an experienced technician. They can determine the root of your problem.