UPVC Window Handle Replacement

Replacing a broken window handle is a easy process, and, with the right tools, it can be done quite quickly. It is essential to know what kind of handle you have and its spindle size before purchasing an alternative.

Older uPVC window handles have a spur that extends and is locked over the wedge striker for cockspur. They can be left- or right-handed and must match when replaced.

What kind of lock and handle do I have?

There are many windows locks and handles made of upvc each with their particular advantages and uses. The type of handle you are using will determine how easy it is to open your windows and if the locking mechanism functions as intended. With time and regular use, the upvc handles on your windows can become damaged and worn out. This makes them less secure and less effective. In some cases they may even fall completely off. It is important to repair your upvc window handles as soon as you begin to notice them falling off. This will stop potential burglaries and ensure your home is secure.

It's a task that anyone can complete. With just a few tools and the right information it's a simple procedure that shouldn't take more than a couple minutes. It is important to be aware of the type of handle or lock that you have on your window. This will help you choose the correct replacement.

Inline Espagnolette Handles

They are the most popular type of upvc handles and are typically located on the side of your window. They are flat in design and come with a latch that engages with the locking mechanism of the frame of the sash window replacement when it is turned. Inline upvc handles feature an elongated spindle that runs through middle of the handle to the window frame in order to operate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are held to the window frame by a single screw and are less secure than other varieties of window handles.

Handles that can tilt and turn

The tilt and turn handles differ from other upvc handles because they can be rotated to open the window and then lowered into the window to allow air circulation. They feature a 7mm spindle on the back and are available in right and left-handed versions.

When you are purchasing replacement handles for replace upvc window Handle upvc, it is important to check the spindle length since not all of them are the same size. Drop something in the middle of the hole to test the length. This is the length of the spindle that will fit in your window.

What is the spindle?

uPVC window handles function similarly like doors. By turning the handle, you are able to operate a latch within the frame. The window can then be opened and closed. However, sometimes these handles can become damaged, particularly when they are used frequently or exposed to extreme weather conditions. You may have to replace upvc Window handle the handles on your uPVC window if they are not functioning correctly.

There are many types of uPVC handle options, such as Espag, Cockspur, and Spaded handles. They are designed to fit inside the uPVC frames in various ways and each handle type utilizes a specific spindle to secure the mechanism into the window. This is why it is essential to know what kind of handle is installed on your uPVC window so you can find the right replacement for it.

The base of the handle will tell you what kind of uPVC it is. A snap-in cover is over the screw that holds the base of the handle in place. Remove this and then you should be able see the second screw at the opposite end of the base portion of the handle. Once both screws have been removed, you should be able take the handle out of the uPVC.

After you have removed the uPVC window handle you need to carefully remove the old spindle from the locking mechanism. Take note of the length of the spindle. You'll need to purchase a new one that is the same length as the handle that was originally used and the locking device.

The main issue with most window handle problems with uPVC is that the spindle becomes worn-out and is unable to longer operate the locking mechanism. This could be due to corrosion, damage from constant use or an unreliable locking mechanism. If this occurs, you will have to replace both the window handle and the locking mechanism to restore the full functionality of your uPVC Windows.

How do I remove my old handle?

Window handles can be damaged or broken over time. It is important to fix them as soon as possible to ensure your safety. The good news is that replacing a damaged or worn handle is a relatively simple job that can be accomplished in just over one minute and doesn't require any specialized tools.

The first step in removing the handle that was previously used is to remove the screw that is situated at the top of the handle base. Once this is removed the handle will be pulled away from the base section. Another screw will be situated at the base of the handle. This can also be removed. After these two screws have been removed, the handle will be removed from the base of the window.

After the handle has been removed, grab the new handle and line up the fixing holes with the holes that are currently in the window frame. There might be a small sticker or caps on the new handle, so take them off the caps if needed, and then put the handle in the frame. It is essential to ensure whether the handle functions after it is installed. Turn the handle over and make sure that the lock mechanism is working.

Espag handles have a spindle that protrudes from the handle and slot into a multipoint locking mechanism inside the frame of the window. Cadenza windows have a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hook over the frame that surrounds the window or the transom crossmember of the bar.

Once you have the new handle in place, slide the spindle inside the lock in the window and then tighten it. Replace the snap-in cover and screw cap (if necessary) once the handle has been firmly fixed. When the handle is ready for use, you can open and close the window a few times to ensure it works correctly and securely.

How do I install the new handle?

The process of changing your window handle made of uPVC isn't difficult and the process is simple. All you need is a screwdriver and a little bit of patience. The first thing to do is ensure that the handle you have previously used is in the unlocked position and then remove any screws that are visible. you can also replace them by screw caps if you need. After removing the handle, you will need to note the length of spindle that extends from the back. This is crucial because it will determine the kind of handle you will need to buy.

Espagnolette handles are the most common type of handle for uPVC windows. They have a spindle that is inserted into the handle and acts as a locking mechanism inside the window frame. When the handle is turned, it releases the latch on the window, allowing it to open. As time passes and with regular use, espagnolette handles may be damaged or damaged, making it necessary to locate an alternative.

Cadenza handles are a type of uPVC handle that is usually used with tilt and turn windows. They have a protruding blade that operates the multipoint locking mechanism inside the window. They are generally more secure than handles made of espagnolette because they are only accessible from the inside. You can replace them with the same method that you would do for handles made of espagnolette however, make sure that the new handle is not angled and flat.

After you have picked the correct handle, you can align the new handle with the existing screw holes prior to screwing it in place. Then, you should put the screw covers on and test your new handle. This is accomplished by moving the handle from the locked to the unlocked position and the reverse direction several times. It may be worth contacting an expert to determine how you can fix any problems. They can often advise you on the best approach to resolve the issue in a fast and effective manner.