Reasons Your Fiat 500 Key Fob Won't Work

A key fob from Fiat 500 is a handy way to unlock the doors and get started the car. However, there are many reasons why the fob won't be functioning. This includes a dead coin-battery or water damage, receiver modules issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). Includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob that isn't working. Modern key fobs have a limited range of operation and must be within a few inches of your vehicle in order to work. If you're far from your vehicle and press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the battery on your coin cell (Part number CR2032) with a fresh one from a reputable manufacturer such as Panasonic, Duracell, or Energizer. They are available at your local hardware store, or online.

You can test the battery on your coin-cell by pressing the buttons while standing near your fiat 500 key fob programming 500 key replacement cost - browse around here - 500. The car should blink its parking lights, and the key fob will operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it might have water damage that prevents it from communicating with the receiver module in your vehicle. Water damage can occur in a variety of ways, ranging from the slightest splash to submerging the fob into salt water at the beach. If you suspect your fob has been exposed to water, you can try placing it in a dry rice bag to pull the moisture out. If this doesn't work, the fob might need to be reprogrammed by an experienced auto locksmith or dealer.

Water Damage

The fob does have rubber seals to keep water from the electronic chip inside it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob that can cause it to short out and eventually end up dying. It's not good to let the fob get wet however, but don't give it up in the event that you accidentally drop it in water or forget to take it out of your pocket.

Remove the battery first. Clean the electronic chip using isopropyl alcohol or a similar product and then dry it completely before replacing the battery. Check the fob to verify if it's working. If the fob doesn't function, it may need to be reprogrammed. This is usually handled by an auto locksmith or dealer.

If the key is newer and has not been programmed to your car It will most likely need to be replaced completely. This is an easy process that can be carried out by a professional automotive locksmith. The locksmith must cut the key to match the ignition of your vehicle. The locksmith will also have to program your fob into the vehicle's system. This is a cheap and quick process that can be completed within the same day.

Receiver Module Issues

One of the main reasons your 500 key fob could stop working is because it's out of range. The remote has a maximum range of 30 feet, so when you're too far from your car it will not respond to your commands. You can easily solve this problem by moving the remote closer to your vehicle until it responds.

If your fob won't work after replacing the battery in the coin, also known as a "button", "watch" or "button", it could be due to an issue with the internal circuit board. Reprogramming the fob is usually the solution to this issue. You can find directions on how to do this on the majority of automobiles by searching YouTube or consulting the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in the correct position. If they lose tension, it could prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob might be out of the vehicle's sync because due to hardware or software issues. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances the software might require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This could occur if the key fob is close to radio transmitters (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob might not work because of a weak connection to the buttons water damage or damage to the internal chips.

If your key for fiat 500 fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. It could be a defective 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, is able to pick up radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's onboard system, including the keyfob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electric current, and Fiat 500 Key Replacement Cost also restart the computer of your car. This can help get your key fob working again. If the issue persists it is recommended that you consult an experienced technician. They'll be able determine the root of your problems.