Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are easy to maintain and durable, as well as long-lasting. As opposed to aluminium and timber they do not rust or rot.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will help prevent unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it can cause a huge deal of damage to your home, which can make it extremely dangerous and possibly fatal. You should take the time to make sure that your windows are in good working order.

For single pane windows, it is fairly easy to replace them, and the replacement will generally fit within the frame that was previously installed easily. However when you have double pane windows that are anchored by internal beading, it'll be more difficult to take out the existing panes and install new ones. In this case, you will need to source some plastic spacers to help the new pane to fit properly into the frame of the window.

If you plan to attempt to remove the window panes yourself it is crucial to wear the proper safety gear that includes gloves with a thick layer of material and protective eyewear. It is also recommended to lay down a dropcloth before you begin working on the glass so that any fragments of glass fall on the fabric rather than on the floor where they can be trampled on and cause further damage.

Once the glass has been removed from the window, it's best to seal the gap with packaging tape or duct tape to block water and drafts from entering the home until a professional can come out and fix the window. It also acts as a barrier, deterring any intruders from getting access to your home. If the gap is particularly large, you might think about a security door that has an integrated window, as it offers the best of both worlds.

2. Sagging

Upvc is a long-lasting and energy efficient alternative to timber sash windows. However, with time, they are susceptible to a range of issues like sagging. A sagging Upvc window repair window can cause issues with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it's crucial to act fast to stop the issue from getting worse.

To repair a window that is sagging, you can try repositioning the hinges. To accomplish this, you'll need open the window to access the frame. With an screwdriver, unscrew the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after you have moved your hinges. If you are happy with the fit of your window, tighten the screws to keep them in the right position.

If you can't reposition the hinges you may require replacing the seal. Over time, rubber seals lose their elasticity and become dry which causes their tightness to decrease. It is important to replace your seal as quickly as you can in order to ensure that your upvc window repair window waterproof and draughtproof.

uPVC handles may also loosen up. This is often caused by screws that have been removed over time, but it could also be due to the mechanism of the handle getting worn out. It's fairly simple to repair a loose uPVC handle. First, you'll need close your window and do an experiment to ensure that it fits. The joints at the corners of the sash should align with the joint on the casing. If it isn't you can use a screwdriver to loosen the handle. Then turn the mechanism into position.

3. Water Leaks

It is essential to act if you awake each day to find a smoky wall and floors that are wet. Leaks of water from windows can cause structural damage to your home and also affect your ability to regulate the temperature in your home. Most of the time, upvc window repair window leaks are caused by a lack or damage to the sealant.

It is a fairly easy fix and Upvc Window repair should be undertaken by any DIY expert. Depending on the severity of the issue is, old caulking may have to be removed. It is important to keep in mind that when it comes to uPVC window repairs you should avoid the temptation to "over-caulk in order to make the area harder to clean and could decrease the efficiency of your energy usage.

Verify that the drainage holes do not have debris in them, and also ensure that the sill pan is properly angled to allow the water to drain from the window. In more serious cases you might have to consider replacing the window.

Other indicators of water leakage include sills that are rotten and the appearance of black spots of mold on the wall near the window. The fungus thrives in humid conditions and can propagate quickly throughout the house.

If the leakage is occurring between the double-glazed glass it is more likely that the issue is related to the seal, not the frame. It is also possible to be fixed by an uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be the reason when your uPVC window is difficult to open or it opens in a breeze. They can be replaced by any competent DIYer and can usually be done within a few minutes.

Like any mechanical part, hinges can wear out over time. Changing a window hinge is essentially a very simple procedure, but it is simpler when you have a person to help you hold the frame in place.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. Look for the arrows on each hinge to determine the direction in which the window should be opened.

The problem can be caused by opening the window improperly or due to a poor installation at the factory. Sending us a photo via our website will often resolve the problem. We are always happy to provide advice.

It is also essential to grease the hinges regularly. This can be done by applying a light engineering oil on the hinges. We suggest using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window operate and close more smoothly. It can also stop corrosion and reduce the possibility of sticking. Ideally, you should do this at least once a year. WD40 and other solvent-based lubricants should not be used since they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different things. First, the hinges because of wear and tear, may become displaced, which will cause a gap to form between the sash and the frame. They can be repaired by giving them a good cleaning, but when they're beyond repair, it may be necessary to get them realigned or replaced. The interlock, which is located on the hinge side of the window, can also be misaligned, and again it is possible to give them a clean but in certain cases, it may be necessary to have these replaced.

The seals may wear out or get damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help regulate indoor temperatures, and reduce the possibility of draughts.

The final method to cut down on draughts effectively is by using a Draught-exclusion device. These are usually fabric tubes filled with a filler that can be put on top of your window sill. They will help stop cold air from entering and keep your home warm and cosy!

With a bit of regular maintenance and repair your windows made of upvc will continue to provide excellent security and insulation for your home. However, it is important to recognize that all windows have a life span and eventually, they will reach the point when it's more economical to replace them than fix them. So, if you're experiencing issues with your Upvc windows, it is recommended to seek help from a professional as soon as possible.