UPVC Window Handle Replacement

Replacing a broken window handle is a easy process, and, with the right tools, it can be done quickly. It is important to know your type of handle and its spindle's length prior buying a replacement sash windows.

Older uPVC windows use handles with cockspurs, which have spurs that protrude to lock over a cockspur wedge striker plate. They can be right-handed or left-handed and should match when replaced.

What kind of lock and handle do I need?

There are a variety of windows locks and handles made of upvc each with their distinct advantages and functions. The type of handle you have will determine whether or not your locking mechanism is efficient and also if it is simple to open the windows. Over time and through regular usage, the window handles made of upvc may become damaged or worn out, rendering them less effective and secure. In some cases they may even fall completely off. It is essential to fix the handles on your window made of upvc immediately if you see them falling off. This will prevent possible break-ins and ensure that your home is secure.

The good news is that replacing your window handles made of upvc is a relatively simple task that is achievable by almost everyone. With just a few tools and the right knowledge it's a straightforward procedure that should take no more than a couple minutes. To begin, you will need to determine the type of lock and handle that you have on your upvc window to help you identify the best replacement.

Inline Espagnolette Handles

They are typically located on the sides of the window. They are flat and come with a latch which engages the locking mechanism of the window frame. Inline upvc handles have a spindle that runs through the middle of the handle, and into the window frame to operate the latch.

Cockspur Handles

They are usually found on older uPVC windows and feature an distinctive hook-shaped design. Cockspur handles have one screw that secures the handle to the frame of the window and aren't as secure as other kinds of window handles.

Handles that turn and tilt

The tilt and turn handles differ from other upvc handles in that they can be rotated for opening the window, and then lowered into the window to ventilate. They feature a 7mm spindle on the back and are available both in left and right-handed versions.

It is important to measure the size of the spindle when purchasing a replacement handles made of upvc. There are a few that are exactly the same size. Drop something in the middle of the hole to check the length. This is the length of the spindle that will be suitable for UPVC Window Handle Replacement your window.

What is spindles?

uPVC window handles operate in a similar way as doors. By turning the handle, you are able to open a latch in the frame. The latch opens the window, to allow it to be closed and opened. The handles can become damaged, especially if they're used frequently or exposed to harsh conditions. It is possible to replace the handles on your uPVC window if they are not functioning properly.

There are a variety of uPVC handles that are available, including Espag, Cockspur and Spaded handles. These handles are designed in a variety of ways to fit into uPVC frames. Each handle style uses a different spindle to lock the window mechanism. This is why it is important to identify the type of handle you have installed on your uPVC window to get the correct replacement.

The base section of the handle will tell you what type of uPVC it is. There should be a'snap in cover over one screw which holds the handle base in place. When you remove this cover you will be able to see the screw that holds the base of the handle in place. After both screws are removed, you should be able take the handle out of the uPVC.

Once you have removed your uPVC window handle, you have to carefully unscrew the spindle that was previously attached to the locking mechanism. Be sure to note the length of the spindle as you'll need to make sure that you purchase a replacement that has the same length as the original handle and locking mechanism.

The primary issue with window handles made of uPVC is that the spindle becomes worn out and cannot longer work with the locking mechanism. This can be caused by corrosion, damage caused by constant use or the locking mechanism becoming looser. When this happens it is necessary to replace the window handle and the locking mechanism to restore full functionality to your uPVC windows.

How do I take off my old handle?

Window handles can become damaged or even broken over the course of time. It is important to fix them as quickly as possible to ensure your safety. It is simple to replace window glass near me a worn or damaged handle. The task can be completed in under an hour without the need for special tools.

To remove the old handle, you must first remove the screw at the bottom of the handle. Once this is removed the handle can then be pulled away from the base section. There is another screw located at the bottom of the handle's base, and it can be removed too. After these two screws have been removed, the handle can be detached from the base of the window.

Once the old handle is removed, grab the new handle and line up the fixing holes with the holes present in the window frame. There may be a little cap or sticker on the new handle, so remove them if needed and then screw the handle into the frame. It is important to check whether the handle functions after it is put in place. Turn the handle around and ensure that the lock mechanism is working.

Espag handles come with spindles that protrude from the handle and slot into the multipoint locking mechanism that is on the window frame. Cadenza windows have an edge with cut-outs which slot into the lock mechanism, while Cockspur handles have an extended nose that hangs over either the frame's outer or transom bar cross member inside the window.

Once you have the new handle in place, slide the spindle inside the lock in the window and then tighten it. Once the handle is securely fixed then replace the snap-in cover and screw cap (if applicable). Now that the handle is ready to use, open and close the window a few times to make sure that it functions properly and securely.

How do I install the new handle?

It's not difficult to alter the handle on your windows made of uPVC. The procedure is easy. All you need is a screwdriver, and a little bit of patience. First, make sure that the old handle is unlocked. Remove any screws that are visible. You can also replace them with screw caps. Once the handle is removed it is necessary to take a note of the length of the spindle that extends from the back of the handle. This is crucial because it will determine the kind of handle to buy.

Espagnolette handles are the most commonly used kind of handle that is used on uPVC windows. The spindle is inserted into the handle to operate the locking mechanism within the window frame. When the handle is turned it opens the latch on the window, allowing it to open. As time passes and with regular use, espagnolette handles can become damaged or impaired and it is necessary to locate an alternative.

Cadenza handles are a second type of uPVC window handle commonly used on tilt and turn windows. They feature a protruding blade that is operated by a multi-point locking mechanism within the window. They are more secure than an espagnolette handles since they only open from the inside. You can replace them with the same method as you would do for handles made of espagnolette however, make sure that the new handle is angled, not flat.

Once you have decided on the right handle to purchase then you can align the new handle with the existing screw holes, and then screw it in place. After that, you can put the screws on and test the new handle. You can perform this by dragging the handle back and forth from the locked position to the unlocked a few time. It is possible to contact an expert to see whether you can solve any problems. They can often advise you on the best way to solve the issue in a quick and effective way.