UPVC Window Handle Replacement

Replacing a damaged window handle is a relatively simple process and with the right tools it can be done quickly. But it's essential to know your type of handle and the spindle's length prior to purchasing the replacement.

Older uPVC window handles have a spur which protrudes and locks over the cockspur wedge striker. These can be either right or left-handed and have to match when replacing.

What type of lock and handle do I need?

There are a variety of window locks and handles made from upvc each with its distinct advantages and functions. The type of handle that you choose will determine if the locking mechanism you have is effective and if it is easy to open windows. As time passes and with regular use, window handles made of upvc are prone to wear or damage. out, making them less secure and efficient. In certain instances, they might even fall completely off. If you notice that your upvc window handles have been removed, it's important to repair them as quickly as possible. This will stop potential burglaries and ensure your home is secure.

It's a simple job that almost anyone can do. With just a few tools and the proper knowledge, this is a simple procedure that should take no less than a few minutes. It is important to know the type of handle or lock that you have on your window. This will allow you to choose the appropriate replacement.

Inline Espagnolette Handles

These are the most common type of upvc handles and are usually located on the outside of your window. They are flat and come with an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles have spindles that run through the middle of the handle, and into the window frame to operate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are secured to the frame of the window by one screw, and are less secure than other types of window seal replacement handle.

Tilt and Turn Handles

The tilt and turn handles differ from other handles made of upvc in that they can be turned to open the window glass replacement and then lowered to the window to let air circulate. They have a 7mm spindle on the back and are available both in left and right-handed versions.

When you are purchasing replacement handles for upvc It is crucial to measure the spindle's length since not all of them are identical in size. To test the length of your handle made of upvc, simply drop something in the middle of the hole, and upvc window handle Replacement then measure how far down it goes before it reaches an obstruction. This is the largest spindle size that will fit your windows.

What is the spindle?

uPVC window handles function in a similar manner to doors. By turning the handle, you are able to activate a latch inside the frame. The window is then opened and shut. But, at times, the handles may become damaged, especially when they are frequently used or exposed to harsh weather conditions. This can lead to the need to replace your uPVC windows handles as they might not be able to operate the window properly anymore.

There are many different types of uPVC handles, including Espag, Cockspur, and Spaded handles. These handles are designed to fit into the uPVC frames in a variety of ways and each handle type utilizes a specific spindle to lock the mechanism to the window. This is why it is crucial to know the kind of handle you have installed on your uPVC window so you can get the correct replacement for it.

The base section of the handle will tell you what type of uPVC it is. A snap-in cover should be over the screw that holds the handle's base in place. Take it off and you should be able see the second holding screw at the opposite end of the base of the handle. Once both screws are removed you should be able to pull the handle away from the uPVC window.

After taking off the uPVC handle, remove it from the locking mechanism. Take careful note of the length of the spindle, as you'll need to make sure that you purchase a replacement that has the same length as your original handle and locking mechanism.

The primary issue with uPVC window handle problems is that the spindle becomes worn-out and is unable to longer work with the locking mechanism. This can be caused by corrosion, damage caused by constant use or a loosening locking mechanism. When this happens it is necessary to replace the window handle as well as the locking mechanism to restore full functionality to your uPVC windows.

How do I remove the old handle?

Window handles can be damaged or broken over time. It is important to fix them as soon as you can to ensure your safety. It is simple to replace a worn or damaged handle. The task can be completed in less than one minute without the need of special tools.

To take off the handle, you must first remove the screw that is located at the bottom of the handle. Once the screw is removed, the handle can be pulled away. A second screw will be situated at the base of the handle. This too can be removed. After the two screws are removed, the handle can be detached from the window's base.

After removing the old handle and align the fixing holes of the new handle to the holes already present in the window frame. There may be a little cap or sticker on the new handle, so take them off them if needed and then screw the handle into its place. Once the handle is in place, it is important to test that it is working by turning the handle and ensuring that the lock mechanism activates.

Espag handles have an elongated spindle that extends from the handle and slot into a multipoint locking mechanism inside the window frame. Cadenza windows have an edge with cut-outs which slot into the lock mechanism while Cockspur handles have an extended nose that hangs over either the outer frame or transom bar cross-member within the window.

Once you have the new handle in place, you can insert the spindle into the lock inside the window and then tighten it. When the handle is fixed, replace the'snap in' cover and the screw cap (if necessary). When the handle is ready for use, open and close the window a couple of times to make sure it is working properly and securely.

How do I install the new handle?

Changing your uPVC window handle isn't difficult, and the process is simple. All you require is a screwdriver and small amount of patience. The first thing to do is to ensure that the handle you have previously used is in the unlocked position and then remove any screws that are visible, you can replace them by screw caps if you need. After removing the handle you'll need to take note of the length of the spindle which extends from the back. This is important as it will determine the type of handle that you will need to buy.

Espagnolette handles are the most popular type of handle used on uPVC windows. The spindle passes through the handle to operate the locking mechanism in the window frame. The handle releases the latch, allowing the window to open. As time passes and with regular use, espagnolette handles could be damaged or damaged and it is necessary to locate an alternative.

Cadenza handles are another type of uPVC window handle, which is typically used on tilt and turn windows. They have a protruding blade that operates an interlocking mechanism that is multipoint within the window. They are usually more secure than handles made of espagnolette because they can only be opened from the inside. They can be replaced using the same procedure as espagnolette handles, however you should ensure that the new handle has an angled blade instead of a flat one.

Once you have selected the correct handle, simply align the new handle with the existing screw holes before fixing it with screws. Then, put the screw covers on and test the new handle. This is accomplished by moving the handle from the locked position to the unlocked and the reverse direction a few times. If you have any issues, it might be worthwhile contacting a professional to see if they can help resolve the problem. They can advise you on how to solve the issue in a quick and efficient manner.