Fiat 500 Replacement Key Fob

It could be time to change the battery if your 500 remote key fob isn't working. However, if you replace the battery but it doesn't work the issue could be elsewhere.

At United Locksmith, we specialize in the creation of new keys for classic automobiles. We have all of the necessary tools and parts for this service.

Dead Coin Battery

The most common reason why your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The battery inside the key fob is likely where to get a Fiat key Cut drain quickly when you don't use it often enough. If your remote began to show signs of weakening such as a loss in range and then completely stopped working it is likely that the battery is dead.

The battery inside the key fob is held in place by metal retaining clips. If the clips are not tightly secured, they could result in problems with the contact, which can stop your remote from receiving power. Use a flathead screwdriver to break open the retaining clip and then remove the old battery. Make sure that the battery you choose to use has the same size, voltage and specifications as the original.

Water exposure can also cause the key fob to become corroded or damaged. Even a brief bath in soapy water may damage the electronic chip inside. It is best to keep your key fob in a dry place.

Water Damage

If your key fob isn't operating correctly, it could be due to water damage. The rubber seals on key fobs protect them from being damaged by a slight splash or drizzle of water. However, it is important to keep the car keys away from the washing machine, the ocean, and the pool.

The key fob has an electronic chip in it that transmits a signal car's immobilizer system. The chip allows the 500 to lock and start. If it gets wet it will not function.

If you're trying to determine if your key fob is still functioning you can clean the internal electronics using isopropyl or electronic cleaner. It is recommended to replace the key fob if it's submerged in salt water rather than attempting to fix it yourself.

While a replacement fob could cost a little money, it's far less expensive than having to pay for your Fiat 500 to be towed to a dealership and fixed! You could also do it yourself with only a few steps. Make sure you have the correct type of battery before attempting to open your key fob. This task is much easier than it looks and there are step-by-step instructions online for virtually any key fob for cars.

Faulty Chip

The chip in the key fob connects directly with the immobiliser on your car to ensure that your vehicle will only start when the correct keys are used. If the chip is damaged or damaged the car won't start no matter what you do.

Damage to the water or a dead battery are the two most frequent causes of a faulty chip. Regardless of the reason, it is a good idea to leave the job to a locksmith, as they will be able to repair the chip quickly and at a low cost.

If your key fob does not work after exposure to water that is clean from the tap or rain, remove the battery. Clean the electronic component with a paper towel. If the key fob still does not work it's likely to be a fried chip and where to Get a fiat key cut will require replacement.

Some people will go to their dealer when they are in need of an entirely new fiat key programmer key fob, however it can be a costly option. If you are seeking a cost-effective method to have your Fiat key fob fixed make sure you contact United Locksmith. We have all the tools and experience needed to fix your Fiat fob quickly and professionally. way.

Faulty Receiver Module

Fiat key fobs send an electrical signal to the vehicle that can unlock and lock doors (and start the vehicle for those with an automatic transmission) up to 50 feet. There are many reasons why the fob might not function. This could be due to a dead coin battery, water damage or worn buttons as well as a receiver module problem and signal interference, or a malfunctioning electronic chip.

If the fob was in a pocket which has suffered extreme trauma (such as being dropped onto a hard floor or being washed in the washing machine), it may not be in a position to connect with the Body Control Module (BCM) of the car. The BCM is a security system that can only accept signals from genuine keys.

If this is the case, then you must replace your fob. A professional locksmith is able to handle all aspects of the key replacement process and even program a new one for the 500. In fact, they could offer you a clone key that functions exactly like the original fob (and costs a fraction of the price).