Peugeot 208 Key Replacement

peugeot 308 key fob 208 key replacement should be left to professional auto locksmiths with the right equipment and technical know-how. They can design and program keys faster and less expensive than dealers.

A dead battery for your coin is most likely to be the cause the reason your key-fob stops locking or unlocking doors. There are many other reasons that the key might be malfunctioning.

Dead Coin Battery

A dead battery can stop your Peugeot 208 from locking and unlocking, as well as making it impossible to start the engine. If this is the situation, you'll need make use of the backup starting procedure which is explained in the owner's manual of your vehicle.

Another reason why the 208 won't start is that the spark plugs have been worn down. The spark plugs light the fuel to start the engine. However they are limited in their lifespan. If they aren't used enough and they fail, they'll eventually die.

There is a simple solution to this problem. Verify the voltage of your battery using a multimeter. If the voltage is less than 11,5 volts, it's time to replace it. If the battery has corrosion it is essential to clean its contacts. You can do this by lifting the rubber covers that protect the two terminals on the battery and using wire brushes to clean any parts that are corroded from the battery. Then, you should reconnect the positive and negative pole cables.

Water Damage

If your 208 will not start and the battery has not been replaced, you must examine the spark plugs. You may find that they are simply too filthy and don't spark. The spark plugs can be cleaned in an workshop.

Peugeot cars are equipped with a transponder key that works with the car's immobiliser system. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, it will not send the proper signal to the vehicle.

Water damage is a frequent reason for this issue. This is most common in colder climates, where the vehicle might have been exposed to rain or snow. In this case, you need to contact a reliable locksmith who will have the required tools and equipment to change the key's programming. They also have the latest technological know-how and machinery required to create a Peugeot 208 smart key. The process shouldn't take more than 15 minutes.

Faulty battery contacts

Peugeot changed from the old carbon-encased transponder chips to a new type of chip that relies on electronic components within a circuit board. The new system works great when it's brand new, but the circuit boards begin to degrade with time and stop working properly.

This could stop the immobiliser chip from activating the immobiliser chip, causing your car not to start. If this is the case, it's recommended to get in touch with a Peugeot specialist or locksmith.

Another issue that is common is when the battery in the key fob begins to fail, which causes the key blade to stop from entering the lock. A car locksmith will replace the battery, and then cut a fresh blade for you. This is a quick solution.

Faulty Receiver Module

It could be that the receiver module is faulty in the event that your Peugeot Key Fob (Xilubbs.Xclub.Tw) stops working after being dropped on the floor, exposed to a stormy rainstorm, or accidentally washed. The receiver module is responsible for transmitting radio frequencies to the onboard computer that regulates the central locking system of your Peugeot vehicle.

Rubber seals on the key fob block water from reaching its electronic chip. However prolonged exposure to water can cause damage to these seals and the chip. The high salt content in the ocean or pool can cause damage to the key fob when it is submerged.

The module will have to be replaced if your Peugeot spare key is no longer working. This can only be performed by a professional auto locksmith or Peugeot specialist. As opposed to other cars, Peugeot keys are protected by a unique immobilizer system that requires the correct coding to begin the engine. This is why you must choose a reputable Peugeot locksmith for the job of designing and programming an alternative.

Computer on-board is not working properly

The on-board computer in your Peugeot is responsible for a variety of systems in your car, including power windows and airbags. The on-board computer will show a code when something goes wrong. The code is stored within the system until the problem is fixed. Most often, this involves replacing the on-board computer.

The most frequent cause for the warning light of the airbag to illuminate is corrosion or loose connections in the sensor. This could be due to wear and tear, age or exposure to moisture and salt. This problem should be dealt with as soon as you can, as an airbag that is not functioning could pose a risk in the event of an accident.

If your Peugeot is showing a card that is not being detected error, the battery inside the key fob may be weak or dead. This can prevent the key fob from sending a signal to disable the immobilizer on your vehicle's standard. You can test this by pressing the unlock button on the key fob, then attempting to start your vehicle. If this does not work, then the key battery is in need of replacement.